TM 5-3895-372-24P
F -
Direct support or aviation intermediate is the
lowest level than can do complete repair of the
item.
H -
General support is the lowest level that can do
complete repair of the item.
L -
Specialized repair activity is the lowest level that
can do complete repair of the item.
D -
Depot Is the lowest level that can do complete
repair of the item.
Z -
Nonreparable. No repair is authorized.
B -
No repair is authorized. (No parts or special
tools are authorized for the maintenance of a
"B"-coded item.) However, the item may be
reconditioned by adjusting, lubricating, etc., at
the user level.
(3)
Recoverability
Code.
Recoverability
codes are assigned to items to indicate the disposition
action on unserviceable Items. The recoverability code
Is entered in the fifth position of the SMR code as
follows:
Code
Application/Explanation
Z -
Nonreparable item. When unserviceable,
condemn and dispose of the item at the level
of maintenance shown in the 3d position of the
SMR code.
O -
Reparable
item.
When
uneconomically
reparable, condemn and dispose of the item at
unit maintenance or aviation unit level.
F -
Reparable
item.
When
uneconomically
reparable, condemn and dispose of the item at
the direct support or aviation Intermediate
level.
H -
Reparable Item. When uneconomically
reparable, condemn and dispose of the Item at
the general support level.
D -
Reparable item. When beyond lower level
repair
capability,
return
to
depot.
Condemnation and disposal of item not
authorized below depot level.
L -
Reparable item. Condemnation and disposal
of item not authorized below specialized repair
activity (SRA).
A -
Item
requires
special
handling
or
condemnation procedures because of specific
reasons e.g., precious metal content, high
dollar value, critical material, or hazardous
material).
Refer
to
appropriate
manuals/directives for specific instructions.
c.
FSCM or CAGEC (Column (3)). The Federal
Supply
Code
for
Manufacturer
(FSCM)
or
the
Commercial and Government Entity (CAGE) Code (C) is
a 5-digit alphanumeric code which is used to identify the
manufacturer, distributor, or Government agency, etc.,
that supplies the item.
d.
PART NUMBER (Column (4)). Indicates the
primary number used by the manufacturer (individual,
company, firm, corporation, or Government activity),
which controls the design and characteristics of the item
by means of its engineering drawings, specifications
standards, and inspection requirements to identify an
item or range of items.
NOTE:
When you use an NSN to requisition
an item, the item you receive may
have a different part number from the
part ordered.
e.
DESCRIPTION AND USABLE ON CODE (UOC)
(Column (5)). This column Includes the following
Information:
(1)
The
Federal
item
name
and,
when
required, a minimum description to identify the item.
(2)
Physical security classification.
(3)
Items that are included in kits and sets are
listed below the name of the kit or set on Figure KIT.
(4)
Spare/repair parts that
make
up
an
assembled item are listed immediately following the
assembled item line entry.
(5)
Part numbers for bulk materials are
referenced in this column in the line item entry for the
item to be manufactured/fabricated.
(6)
When the item Is not used with all serial
numbers of the same model, the effective serial numbers
are shown on the last line(s) of the description (before
UOC).
(7)
The usable on code, when applicable (see
paragraph 5, Special Information).
(8)
In the Special Tools List section, the basis
of Issue (BOI) appears as the last line(s) In the entry for
each special tool, special TMDE, and other special
support equipment. When density of equipments
supported exceeds density spread Indicated in the basis
of
issue,
the
total
authorization
Is
Increased
proportionately.
(9)
The
statement
"END
OF
FIGURE"
appears just below the last item description in Column 5
for a given figure in both Section II and Section III.
f.
QTY (Column (6)). The QTY (quantity per figure
column) indicates the quantity of the item used in the
breakout shown on the illustration/figure, which is
prepared for a functional group, subfunctional group, or
an assembly. A "V" appearing in this column in lieu of a
quantity indicates that the quantity is variable and the
quantity may vary from application to application.
3 Change 1
